World Tech

How to Install a CPU Cooler?

Assuming you’ve placed the processor in the socket of the motherboard, the logical next step is to install the processor cooler. Whether you are replacing an original radiator with a secondary radiator or installing an original radiator for the first time, it is quite easy to make a mistake. Improper installation of the CPU cooler, or improper installation of the CPU cooler in general, will cause the CPU to overheat within seconds.

Overheating makes your system unstable and causes crashes, reboots, heat exhaustion and even exhaustion of your processor and motherboard if your processor is old and doesn’t have a built-in system that shuts itself down when it detects dangerous temperatures. Fortunately, installing a refrigerator is fairly simple and can be done by anyone. To install a CPU cooler.

Installation of an Intel Processor Cooler

Anyone who has ever tried to install an Intel processor cooler with pins knows that it is very complicated and not at all intuitive. There are multiple arrows on the buttons and the mechanism seems very intimidating. Fortunately, you can’t go wrong if you follow everything step by step, and you will have successfully installed your refrigerator within minutes. Here’s how.

Step 1 – Application of the thermal paste

Before doing anything to the cooler, apply a thermal paste. If your fridge is brand new, it’s probably already covered in thermal paste. You can check this by turning the cooler of the central unit upside down and looking at the connection. If you see a grey-white mixture that looks a bit like toothpaste, you’re on the right side.

Otherwise, the application of the thermal paste is simple. After buying a syringe of thermal paste, squeeze a pea-sized drop onto it or draw a thin line down the center of the processor. That’s about all you have to do. If the processor has already received thermal pulp, clean it with isopropyl alcohol and a dry cloth or paper towel.

Step 2 – Prepare the bed bugs

If you have just taken your refrigerator out of the box, the pushers should already be installed correctly. Don’t turn them around and confuse them. You can see that there are little arrows on the pushers. The four plungers should be rotated 90 degrees counter-clockwise relative to the CPU cooler radiator. They won’t go any further in that direction. If the plungers are not in this position, simply rotate them so they reset and can be installed.

Step 3 – Aligning the refrigerator

You can see that there are four holes in each corner around the processor connector. These holes are reserved for mounting your CPU cooler, and this is where the push pins should go. Align the CPU cooler so that all the pressure pins are on these holes, but do nothing else. Never pick up the cooler after putting it on the processor, or you will damage the thermal paste and have to start over. Shake the cooler a little to set it in place.

Step 4 – Placing the pins

After making sure all the pins are in place, hold the refrigerator with one hand and push the pins in with the other. Make sure it stays stable and do one corner at a time. Always use the reverse angle after pressing to adjust it correctly and distribute the pressure evenly.

After all four pins are pressed, you can gently stir the fountain to see if you have installed it correctly. If one side comes loose, try removing it and putting it back on.

Step 5 – Connect the fan

Now that your cooler is in place, it’s time to connect the vent strip. This is a 4 pin fan, as opposed to a 3 pin fan, as the fourth pin is used to control motor speed. However, 3 and 4 pin headers and connectors are fully compatible.

Just look for the fan header on the motherboard. The normal position is on the top right side of the cooler, next to the RAM slots. Make sure you align the radiator plug with the pins and plug in, that’s all you need to do. Turn on your computer and visually check that your refrigerator is working properly.

Installing an AMD (Wraith) Processor Cooler

AMD CPU coolers come in two forms. Large coolers like the AMD Wraith Prism use locking clips. Smaller coolers, like the Stealth Wraith, use simple spring-loaded screws. We’ll cover both, just in case.

Step 1 – Application of the thermal paste

As with any refrigerator, a thermal paste must first be applied. You can see how to do this above. But if your cooler is brand new and already covered in thermal paste, you can skip this step.

Step 2 – Removal of pre-mounted brackets (for spring-loaded screw coolers)

If your cooler is equipped with mounting brackets, do not remove the pre-installed brackets that came with the motherboard. You’ll need it. Spring-loaded radiators, however, must be screwed down, so the brackets must disappear. You have to be very careful with this step because once you remove the brackets, the back plate behind the plug is loose.

It is best if someone holds the tampon while you do this and the next step. Once you install the CPU cooler, the back plate will stay in place, but before that it will fall off and there is a small chance it will hit something and damage it, so be very careful.

Step 3 – Mounting the cooler

For a spring-loaded screw cooler, carefully insert the CPU cooler so that all screws are aligned with the holes on the motherboard. The reason the bolts are spring loaded is so the radiator can produce a constant pressure. You don’t have to turn one screw at a time here. Instead, all screws should be tightened slowly and evenly. Tighten the screws only gradually.

For coolers with mounting clips, align the cooler so that the mounting clips are aligned with the motherboard mounting frame, one on each side. Ensure that the locking clips on both sides engage. You will need to use some force to get them in place, but don’t push too hard as you could easily break something. Once the two locking clips are in place, press the cam lever to lock it in place.

Step 4 – Connecting the fan

Just like the Intel cooler, you just need to plug the CPU fan into the fan connector and you’re done. The fan head is located at the top right of the exhaust. If you use an RGB cooler, for example. B. a Wraith prism, you must also connect an RGB LED. You can refer to the motherboard manual to know exactly where it is located. It is probably located directly below the mainframe cooler. Make sure the fan is running when you turn on the computer.

Installation of a spare CPU cooler

Some aftermarket processor coolers use completely different mechanisms than those used by Intel or AMD. However, the vast majority use either mounting clips or screws, just like AMD coolers. You should refer to your refrigerator’s owner’s manual to know exactly how to assemble it. Whatever type of refrigerator you have, you will need to apply a thermal paste if it hasn’t already been applied to the bottom of the refrigerator.

Eventually you will also need to connect the CPU fan, although you may want to do this before installing the cooler if it is very large. Most coolers with mounting clamps can be installed with the AMD brackets pre-installed, but you can also use the brackets that come with the cooler. With Intel, the latter is your only choice.

Completion

The installation of the central cooler is simple. Most people can do it themselves, but there is no shame in having someone help you, especially if there is a back wall. Intel coolers are slightly more difficult to install than AMD CPU coolers with spring loaded screws.

Coolers that use clamps, such as. B. the AMD Wraith prism, are the most difficult to install, because you have to attach both brackets to the mounting brackets, and you have to apply some pressure while doing so. Always use a high quality thermal paste if you do not have a pre-installed paste. In addition, you must never lift the refrigerator after turning it off, as this will cause air bubbles to form in the thermal joint, affecting cooling.

frequently asked questions

Is it difficult to install a CPU cooler?

Is it difficult to replace the CPU cooler? Not really, but it’s a little unsettling. You need to remove the old cooler (usually 4 screws), clean the old thermal paste with alcohol, apply a new layer of thermal paste and install the new cooler. … It’s all a bit twisted.

How do I install a CPU cooler?

To install a CPU cooler : Keeping the processor cool…

Do I need to remove the motherboard to install the CPU cooler?

That depends on the radiator you want to use. The processor comes with an air cooler, but if you want to replace it with, say, a tower model as shown below, you may need to do so, as these types of processor coolers require brackets that attach to the back of the motherboard. … No, you don’t need to remove the motherboard.

Related Tags:

how to install a cpu liquid coolerhow to install a cpu cooler amdhow to install cpuhow to install cpu fan intelhow to install cpu fan on motherboardhow to install cooler master cpu coolerhow to install cpu fan with spring screwshow to replace cpu cooler